Rumored Buzz on chicagoland concrete & waterproofing inc

I've a forty+ 12 months old suspended slab in my garage. The concrete is spalled, uneven and stained with oil along with other things from all the many years of abuse. I have to resurface it because it collects water due to a door seal that will not seal as a result of unevenness of your surface.

I've a question accomplishing a patio add on getting rid of a 10x10 2x4 walls with roof on a existing 10x10 slab inbuilt the 70s home operator included further 10x12 into the 70s slab in 1996 This is a open air patio slab 4" thick.

I have a failing skim coat over concrete brick adjacent to some poured and painted concrete wall. How can I prep? Do I have to get a rotohammer and knock all the skim coat off, or just remove the free materials? What product really should I take advantage of, and do I would like a bonding agent? - Aaron

Look at ten a lot more feedback... Our co-op can be a five story apt setting up. The aged facade is crumbling off. Now we have gotten proposals to repair the previous facade. A single proposal says he will use weldcrete to bond the previous and new concrete.

Can Prime'n Bond be utilized to repair a spalling concreted stem wall. I blasted all the unfastened concrete off. I will be placing back again from a feather edge to close to 3/8" thick. All get the job done is higher than grade. - Ken Vayda

Lana, when pouring a whole new slab or walkway it's import to slope the area absent from the foundation of composition to allow for suitable drainage. The base from the concrete should pack down and also a layer of gravel set see up to provide drainage under slab.

I have a completely new shower that I've only utilized for five days. I've regions that won't dry. Lifted tiles under the areas (all-around drain and also a 2in x6 in part off the wall) I have a sense I've dips in cement, the weep holes are open.

I've an existing 8 x 12 ft. concrete slab on which I system to build a garden shed. The slab edges are certainly not level and flat. They're tapered (unintentional) this kind of which the sill plates for the walls tend to tilt outward. To obtain amount and flat slab edges, I'm thinking of adding a brief suppress around the slab edges, extensive adequate to get a 2 x 4 and deep enough to have the edges degree (might be minimal featheredge, highest three.5 inches, depending on tactic).

Eric, Sakrete Sand Mix modified with Sakrete Bonder and Fortifier (like a bonding agent/primer) is recommended for your venture. It's important that you thoroughly prep the area so that it's free of any bond breakers such as Filth, debris, unfastened content, and so on.

Leon, when implementing tile Read More Here you wish a roughened surface to start out with to make sure that your thin established has a little something to grab on to. Make sure before installing your tile the surface is audio instead of brittle. - Chris Complex Companies

Hi, What is the best Sakrete merchandise for vertical application where the aged concrete has deteriorated to the point the corner has now turn into a rounded edge with deep chunks lacking? Thank you! - Chris

James, you could simply just use any of your concrete mixes to fill the hole. Just thoroughly clean out the hole, combine the material and pour. Nonetheless, my biggest problem could well be code. You need to receive a advice from your area code Office making sure that your job stays within code compliance.

Don, regrettably there's no true deal with for this. It is possible to place and expansion joint substance against the house and afterwards pour concrete to fill the hole.

i have a handicap ramp that's not been sloped right an should pour over the whole ramp to re slope from 1 inch to 1 /eight of a inch would this be a fantastic solution to utilize will it hold on a slope or will it just stream down hill if not could you advocate an item also the place am i able to acquire this Your Domain Name my jobs in palm desert california.

Leave a Reply

Your email address will not be published. Required fields are marked *